How To Configure Nginx as a Reverse Proxy for Apache


    Why Run Nginx and Apache Together

    Both nginx and apache are powerful and effective servers. Apache currently reigns as the #1 server for websites and since its public release in 2006, nginx has taken the world by storm and is now the #2 server for active sites. The reasons for each respective server’s popularity are clear: apache’s power and nginx’s speed are well known. However, both servers do have drawbacks—apache is hard on server memory, while nginx (great at static files) needs the help of php-fpm or similar modules for dynamic content.

    However, one can combine the two web servers to great effect, with nginx as static web server front and apache processing the back end.



    To perform the steps in this tutorial, you will need to have sudo privileges on your virtual private server.


    Install nginx

    To start off, we need to install and configure nginx which will serve the front end of our site.

    Let’s download it from apt-get:

    sudo apt-get install nginx

    Once it has downloaded, you can go ahead and configure the virtual host to run on the front end.

    There are a few changes we need to make in the configuration.


    Configure nginx

    Open up the nginx configuration.

    sudo nano /etc/nginx/sites-available/example

    The following configuration will set you up to use nginx as the front end server. It is very similar to the default set up, and the details are under the configuration.

    server {
            listen   80; 
            root /var/www/; 
            index index.php index.html index.htm;
            location / {
            try_files $uri $uri/ /index.php;
            location ~ \.php$ {
            proxy_set_header X-Real-IP  $remote_addr;
            proxy_set_header X-Forwarded-For $remote_addr;
            proxy_set_header Host $host;
             location ~ /\.ht {
                    deny all;

    The following changes were implemented in the configuration:

    • The root was set to the correct web directory
    • index.php was added on the index line
    • try_files attempts to serve whatever page the visitor requests. If nginx is unable, then the file is passed to the proxy
    • proxy_pass lets nginx the address of the proxied server
    • Finally the "location ~ /\.ht {" location block denies access to .htaccess files, if Apache's document root concurs with nginx's one

    This configuration sets up a system where all extensions with a php ending are rerouted to the apache backend which will run on port 8080.

    Activate the virtual host.

    sudo ln -s /etc/nginx/sites-available/example /etc/nginx/sites-enabled/example

    Additionally, delete the default nginx server block.

    sudo rm /etc/nginx/sites-enabled/default

    The next step is to install and configure apache.


    Install Apache

    With nginx taken care of, it’s time to install our backend, apache.

    sudo apt-get install apache2

    Since nginx is still not turned on, Apache will start running on port 80.


    Configure Apache

    We need to configure apache to take over the backend, which as we told nginx, will be running on port 8080. Open up the apache ports file to start setting apache on the correct port:

    sudo nano /etc/apache2/ports.conf

    Find and change the following lines to have apache running on port 8080, accessible only from the localhost:


    Save and Exit.

    Subsequently, open up a new virtual host file, copying the layout from the default apache file:

    sudo cp /etc/apache2/sites-available/default /etc/apache2/sites-available/example
    sudo nano /etc/apache2/sites-available/example

    The main issue that needs to be addressed here is that the virtual host needs to be, once again, running on port 8080 (instead of the default 80 given to nginx).

    The line should look like this:


    Make sure your Document Root is correct. Save and exit the file and activate that virtual host:

    sudo a2ensite example

    Before we start testing anything out, we need to equip apache with php. Go ahead and install it now:

     sudo apt-get install php5

    Restart both servers to make the changes effective:

    sudo service apache2 restart
    sudo service nginx restart

    Finish Up

    We have set up the VPS with nginx running on the front end of our site and apache processing php on the back end. Loading our domain will take us to our site’s default page.

    We can check that information is being routed to apache is working by running a common php script.

    Go ahead and create the file:

    sudo nano /var/www/info.php

    Paste the following lines into that file:

    phpinfo( );

    Save and exit.


    Finally, you can see which ports are open and which application is on each one by typing in this command.

    sudo netstat -plunt
    Was this article helpful?
    1 out of 1 found this helpful


    Powered by Zendesk